Home Crosswords Crossword: Level 2 – The Crankshaft

Crossword: Level 2 – The Crankshaft

9
34
43
57
58
59
60
61
62
63
65
67
68
69
70
71
72
73
84
90
93
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
130
134
140
143
149
155
159
162
163
164
165
168
174
180
183
190
192
193
194
195
196
197
198
199
202
205
208
211
224
227
230
231
232
233
234
235
236
237
238
239
240
241
242
244
245
246
247
248
249
252
255
258
261
272
274
277
280
283
285
286
287
288
289
290
291
292
293
295
297
302
305
308
311
319
320
321
322
326
327
328
329
330
331
333
336
337
338
339
340
345
352
355
358
361
368
369
370
380
383
385
386
387
388
389
390
391
392
395
405
411
420
421
422
423
424
430
434
435
436
437
438
439
440
441
451
452
453
454
455
456

Across

  • 57-63 :The ___________type also has a damper hub and an inertia mass.
  • 67-73 :After ______________, the main and rod journals of most diesel engine crankshafts are machined to a rough dimension and then hardened to improve surfaces wear characteristics.
  • 103-118 :The ____________-_______________counteracts or opposes the twisting forces.
  • 162-165 :The crankshaft is secured to the block with the ______________bearings and caps.
  • 192-199 :The ______________is heavy mass of steel attached to the rear flange of the crankshaft.
  • 230-242 :A _______________ is a mass of metal located opposite the rod journal.
  • 244-249 :The rear crankshaft seal surface is usually located on the circumference of the flange.
  • 285-293 :________________hardening is a common method used to harden the surface of the journals.
  • 319-322 :Most four cycle pistons will have a running ____________.
  • 326-331 :The damper hub and an inertia mass that are bonded together with a _____________compound.
  • 336-340 :Common name for a split plain bearing.
  • 368-370 :The ____________connect the main and rod journals to form the throws or crank arms.
  • 385-392 :Oil is supplied under pressure to the main bearings through ______________in the block.
  • 420-424 :________________is the distance from the centreline of the main journal to the centreline of rod journal.
  • 434-441 :____________________is usually identified as being either clockwise or counter-clockwise.
  • 451-456 :The crankshaft is maintained in position relative to the block by _______________bearings.

Down

  • 9-159 :Crankshafts used in gasoline engines are manufactured using the ____________ process.
  • 43-193 :A _________________ is the load bearing surface of the crankshaft.
  • 65-190 :_________________marks are used to locate proper placement of dampers and flywheels.
  • 105-455 :The _______________-________________or shafts can be mounted in the cylinder block on either of the crankshaft.
  • 149-274 :The ______________is used as a stress relief in this highly loaded area of the crankshaft.
  • 183-383 :The flywheel also carries the ______-_________which engages with the starter drive for cranking the engine.
  • 202-352 :Excessive out-of-balance condition of the crankshaft is likely to cause____________stress cracks.
  • 211-436 :The _______________ converts the reciprocating motion of the piston and connecting rods to rotary motion.
  • 247-322 :The ___________is usually at the front of the crankshaft and is a mounting surface for a gear and the vibration damper.
  • 295-420 :The crankshaft bearings are coated with _____________as a wear surface.