Home Crosswords Crossword: Level 2 – Piston, Rings and Rod Service

Crossword: Level 2 – Piston, Rings and Rod Service

3
4
5
6
7
8
9
10
11
15
16
17
18
19
20
21
22
23
28
40
52
53
54
55
56
57
58
59
60
61
65
78
90
98
103
107
115
123
126
127
128
129
130
131
132
133
134
136
140
142
146
148
153
157
160
161
162
163
164
165
166
167
168
169
170
171
172
173
176
177
178
179
180
181
182
183
184
186
190
192
196
198
201
203
207
211
217
221
223
225
226
228
232
233
234
235
236
237
238
239
240
241
242
243
244
246
248
250
251
254
257
261
267
271
273
275
276
279
282
286
288
289
290
291
292
293
294
296
298
300
304
307
311
321
323
325
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
346
348
350
354
357
361
371
373
375
379
382
386
396
398
400
404
407
409
410
411
412
413
414
415
416
417
418
419
421
425
429
436
446
450
454
461
468
469
470
471
472
473
474
475
477
478
479
480
481
482
483
484
485
486
487
488
489
500

Across

  • 3-11 :The ________-________________must be measured and compared to the piston pins.
  • 15-23 :Visually inspect the connecting rod bolts or cap screws for thread condition and _______________ bolts.
  • 52-61 :__________-________________pistons measure narrower at the pin bosses.
  • 126-134 :Proper ___________________must be maintained between the pistons, connecting rods and the crankshaft.
  • 160-173 :A bent or broken __________-______________nozzle result in a loss of piston cooling.
  • 176-184 :When installing a _________-__________________to the piston, care must be taken that the gap is at the bottom.
  • 232-244 :__________-_______________piston pins are held in the piston by internal snap rings.
  • 288-294 :To check ________-__________________place each piston ring into an unworn area of the cylinder bore.
  • 327-343 :A type of crack detection for ferrous metals.
  • 409-419 :Excessive clearance between the piston and cylinder wall will result with ___________-______________.
  • 468-475 :_______________piston ring grooves must be measured using a special ring gauge.
  • 477-489 :_______-________________is usually used to check for cracks on aluminum pistons.

Down

  • 3-228 :Always remove the residue from your ______________when checking bearing clearances.
  • 15-190 :________________is generally evidence of a lack of lubrication or a loss of clearance due to overheating.
  • 98-398 :Use a _______-___________________and spread the ring just enough to clear the ring lands.
  • 107-407 :__________-__________________piston pins used in diesel engines are usually bolted to the rod.
  • 136-486 :After the ________-________________ is installed on the piston, the bands are tightened firmly to compress the piston rings.
  • 142-292 :_______________is generally evidence of a lack of lubrication or a loss of clearance due to overheating.
  • 146-471 :__________-__________________are used to remove and install rings while preventing piston ring damage.
  • 176-276 :The outside diameter of the piston ______________is measured 90" to the piston pin bores.
  • 225-500 :Rectangular piston __________-_______________are measured for wear using a new ring and a feeler gauge.
  • 254-479 :Use of a _________-_______________remover prevents ring groove damage.