Home Crosswords Crossword: Level 2 – Rings and Con Rods

Crossword: Level 2 – Rings and Con Rods

29
30
31
32
33
34
51
56
76
77
78
79
80
81
82
84
85
86
87
88
89
90
91
92
93
94
95
101
106
119
121
122
123
124
126
128
129
130
131
132
133
134
135
137
138
139
140
141
142
143
144
148
150
151
156
169
173
175
176
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
198
200
201
206
219
223
225
226
230
232
234
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
255
257
259
262
269
273
275
276
280
281
282
283
284
285
286
287
288
289
290
294
296
298
300
301
305
307
309
312
319
321
323
325
326
330
332
334
337
344
346
348
350
351
355
357
359
362
364
365
366
367
368
369
370
371
372
373
374
376
377
378
379
380
382
384
387
389
394
396
398
401
405
407
409
412
414
419
421
423
426
430
432
434
437
439
444
446
451
455
462
469
471
483
484
485
486
487
488
489
490
491
492
493
496

Across

  • 29-34 :The design of material used on the beam of the rod.
  • 76-82 :A specified ________-______________ is left between the ends of the ring to allow for expansion due to heat.
  • 84-95 : rings lower outside edge has positive contact to create a wiping effect on the down stroke of the piston.
  • 121-124 :The straight _____________joint is the most common type and is widely used on both compression and oil control rings.
  • 128-135 :________-_____________are flexible which allows them to conform to the cylinder wall.
  • 137-144 :_______________plating is used as a coating on some types of piston rings.
  • 180-196 :These rings are stronger and have longer wear characteristics than cast iron.
  • 236-250 :_________-____________ is used mostly for the rails of multi-piece oil control rings.
  • 364-374 :These rings are stronger and have longer wear characteristics than iron rings.
  • 376-380 :____________joints reduce leakage at the ring joint and are used on special applications.
  • 483-493 :____________-_________ has a narrower contact area, which creates higher unit pressure for better control of blowby.

Down

  • 31-206 :The ______-________ design reduces the width of the rod at the parting line so it can be removed through the bore.
  • 51-226 :____________ rings are more resistant to carbon build and sticking.
  • 94-469 :_________________-_________exert force against cylinder wall due to ring tension.
  • 123-423 :______________+______________are most common on bias cut connecting rods.
  • 150-350 :Some rod caps are aligned with _____________-_____.
  • 150-350 :Some rod caps are aligned with _____________-_____.
  • 230-455 :______________is used as a coating to provide piston rings with excellent wear and anti-scuff properties.
  • 232-432 :_________-_____________is a low cost material used for piston ring construction.
  • 234-434 :Usually encloses the babbit bearing shells.
  • 237-487 :Wear surface on the side of the large end.
  • 276-451 :Some rod ends have ____________ joints for cap alignment.
  • 296-496 :The little part of the connecting rod.
  • 364-439 :__________joints reduce leakage at the ring joint and are used on special applications.